Toshiba BMS-CT1280UL Manual Download Page 60 | Manualshive

Page: 60 / 167

background image

4

-EN

Air Conditioning Control System (Touch Screen Controller)

Installation Manual

CAUTION

• Do not install in the following locations:

Locations where combustible gas may leak
Locations with high humidity or water
Dusty locations
Locations in direct sunlight and locations subject to high temperatures
Locations within 3.28′ (1 m) from televisions or radios
Outdoors, under awnings, or other locations exposed to rain and dew
Locations exposed to outside air containing corrosive gases or salinity
Locations with frequent vibrations

• Do not operate the touch panel with mechanical pencils or other pointed objects.

• In installation work, use wiring with the correct ampacity.

Failure to do so may result in excessive heat or fire.

• Use specified cables and connect them securely, and do not subject connecting

terminals to external force.

Doing so may result in broken cables, excessive heat or fire.

• Always install a circuit breaker on the primary side of the power supply.
• Clean the touch panel by wiping with an eyeglasses cleaner or other soft cloth.

To remove oil-based ink, wipe with a cloth that has been moistened with a neutral
detergent and then wrung out, and finish by wiping with a soft, dry cloth.

Do not use commercial OA cleaners, cleansers, or other liquid cleaners containing
abrasives.

• When attaching to a metal lath, wire lath or wooden structure with metal boards,

attach it to the control panel, etc. without attaching it to the wall.

CAUTION

This device uses a lithium battery. Follow all local regulations when disposing of it.

«
...
58
59
60
61
62
...
»

Summary of Contents for BMS-CT1280UL








































































































































































Reviews:

No comments

Related manuals for BMS-CT1280UL

Brand: FAAC Pages: 12

Brand: ABB Pages: 63

Brand: Mackie Pages: 16

Brand: TANDBERG Pages: 47

Brand: Zodiac Pages: 12

Brand: National Instruments Pages: 34

CIATControl OPC Server

Brand: CIAT Pages: 32

Brand: Danfoss Pages: 8

Infi 90 IMAOM01

Brand: Bailey Pages: 44

Brand: Euromatic Pages: 20

Brand: VMK Pages: 98

AQUIS ULTRAFLOW

Brand: Waterous Pages: 217

Brand: Simpnic Pages: 16

Brand: Grundfos Pages: 80

TotalArc BMS 460346 SOLAR POWER

Brand: OGI Pages: 28

Brand: FUTABA Pages: 6

Commander Site Controller

Brand: VeriFone Pages: 34

KaDe KDH-KZ620U

Brand: AAT Holding Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands