Toshiba BMS-CT1280UL Manual Download Page 108

Page: 108 / 167

Touch Screen Controller

Owner's Manual

-EN

●

NOTE

• For the setting of [(1)], see "Local Remote Controller Lock" (P.40).
• For the setting of [(2)], see "Set Operation Details" (P.42).
• If there is no corresponding function, that item is not displayed.

Fan Speed

Tap to switch to the following.

●

NOTE

Fan speeds that cannot be set are not displayed.

Set temp.

Tap

to change the set temperature.

●

NOTE

• If the operation mode is FAN, the temperature cannot be set.
• "Control temp." shows the indoor temperature detected by the outdoor unit.

*Depending on conditions such as the installation site of the indoor unit, it may differ from

actual room temperature.

Example of a model without a flap

Example of a model where only a certain fan speed
can be set

Since you cannot set the air direction, it does not change even
if you tap it.

Since you cannot change the fan speed, it does not change
even if you tap it.

No.

Name

Functions

(1)

(2)

Summary of Contents for BMS-CT1280UL







































































































































































Search results

Summary of Contents for BMS-CT1280UL

Reviews:

Related manuals for BMS-CT1280UL

Brands by name

Popular brands

Toshiba BMS-CT1280UL, Manual

Search results

Summary of Contents for BMS-CT1280UL

Reviews:

Related manuals for BMS-CT1280UL

Brands by name

Popular brands