Toshiba BMS-CT1280UL Manual Download Page 4

Page: 4 / 167

• If you have to inspect a circuit that is energized, for example, take precautions

such as wearing rubber gloves to avoid direct contact with a live part

Touching a live part may result in an electric shock.

• Check that there are no abnormalities after completing the repair work

Failure to perform this check may result in fire, electric shock, or injury.
Turn off the earth leakage breaker before performing an inspection.

• After completing the repair work, perform a test run and check that there are no

abnormalities such as smoke or unusual noise

Failure to perform this check may result in fire or electric shock.
Perform a test run after installing the front panel and cabinets.

• Installation and reinstallation work should be performed by your vendor or a

qualified electrician

Attempting to carry out installation work on your own, and doing so incorrectly, may result in
electric shock or fire.

Risk of electric shock

Check after repair

Repair and reinstallation

work

Summary of Contents for BMS-CT1280UL







































































































































































Search results

Summary of Contents for BMS-CT1280UL

Reviews:

Related manuals for BMS-CT1280UL

Brands by name

Popular brands

Toshiba BMS-CT1280UL, Manual

Search results

Summary of Contents for BMS-CT1280UL

Reviews:

Related manuals for BMS-CT1280UL

Brands by name

Popular brands