Toshiba BMS-CT1280UL Manual Download Page 106

Page: 106 / 167

Touch Screen Controller

Owner's Manual

-EN

* About confirmation pop-up selection

Check the contents of the message and tap [

-(1)

]

When the screen on the left appears, check the contents
of the message and tap [

-(1)

] or [

-(2)

]

The settings of the entire group are changed.

-(1)

-(2)

Air Conditioning

Control System

If you select [No], only air conditioners are subject
to operation.

If you select [Yes], both air conditioners and ON/
OFF unit are subject to operation.

Air conditioner

Group

If you select [No], only air conditioners are subject
to operation.

If you select [Yes], both air conditioners and ON/
OFF unit are subject to operation.

Air conditioner

Group

ON/OFF unit

General purpose

device control I/F

Air to Air Heat Exchanger

External device

External device (DI/DO)

ON/OFF unit

General purpose

device control I/F

Air to Air Heat Exchanger

External device

External device (DI/DO)

Summary of Contents for BMS-CT1280UL







































































































































































Search results

Summary of Contents for BMS-CT1280UL

Reviews:

Related manuals for BMS-CT1280UL

Brands by name

Popular brands

Toshiba BMS-CT1280UL, Manual

Search results

Summary of Contents for BMS-CT1280UL

Reviews:

Related manuals for BMS-CT1280UL

Brands by name

Popular brands