manualshive.com logo in svg

Toshiba B-SX4T Series, Specification

Share
Download
Toshiba B-SX4T Series Specification Download Page 8

 

- 4 -

Main PC board 

 

MAIN4-R or greater 

MAIN3-R or earlier 

Boot 
program 
earlier than 
V3.0 

When the boot program is sent to 
the printer by the downloader, the 
printer shows “MODEL TYPE 
ERROR” on the LCD and results in 
an error.   
When the COM is used as the 
interface, the downloader shows 
“Check Sum Error”. (Then, the 
printer is forcibly shut down.) 
After the printer is restarted, it starts 
up in the previous status 

Downloaded normally. 

 

Main 
program 
earlier than 
V5.0 

When the main program is sent to 
the printer by the downloader, the 
printer writes the program, shows 
“FIRM VER. INVALID” on the LCD, 
and results in an error.     
When the COM is used as the 
interface, the downloader shows 
“Erase Error”.    (Then, the printer is 
forcibly shut down.)   
After the printer restarted, it starts up 
in the DOWNLOAD MODE. 
Downloading the main program V5.0 
or greater enables a recovery from 
the erroneous state 

Downloaded normally. 

 

Summary of Contents for B-SX4T Series























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands