Toshiba B-SX4T Series Specification Download | Manualshive

Page: 196 / 374

background image

- 192 -

In case that the size of BASIC file storage area is set to “AA”:

(9) When this command is received, the BASIC file storage area is reserved and the

other areas in flash ROM on the CPU board are cleared.

(10) If this command is not sent, the storage area in flash ROM on the CPU board

cannot be used.
If “AA” is set for the size of the BASIC file storage area with the BASIC file storage
area being unallocated, the BASIC file storage area remains unallocated.

(11) The storage areas except for the BASIC file storage area are allocated in the

following order of precedence – the TrueType font storage area, and the bit map
writable character storage area. After these storage areas are allocated, the
remaining area is used for the PC save area.

(12) If the sum of the TrueType font storage area and the bit map writable character

storage area, specified by this command, is the size of ‘896 KB minus the BASIC
file storage area size’, the TrueType font storage area and the bit map writable
character storage area are allocated as specified. In this case, however, there is
no PC save area.

(13) If the sum of TrueType font storage area and the bit map writable character

storage area, specified by this command, exceeds the size of ‘896 KB minus the
BASIC file storage area size’, the TrueType font storage area is allocated as
specified with the highest priority. Then, the remaining area is allocated to the bit
map writable character storage area. There is no PC save area.

(14) When “00” (0 KB) is specified for each of the TrueType font storage area and the

bit map writable character storage area, the storage area is not allocated.

(15) If the size of ‘896 KB minus the BASIC file storage area size’ or more is specified

for either the TrueType font storage area or the bit map writable character storage
area, each area other than the BASIC file storage area is allocated as specified.
For example, when setting “10” or “11” for the size of the TrueType font storage
area while the BASIC file storage area secures “4” (256KB), the entire storage
areas except the BASIC file storage area are allocated to the TrueType font
storage area. There is no bit map writable character storage area or PC save
area.

Refer to

• Bit Map Writable Character Command ([ESC] XD)

•  Save Start Command ([ESC] XO)
•  Flash Memory Format Command ([ESC] J1)
•  2-byte Writable Character Code Range Command ([ESC] XE)

Example

The TrueType font storage area and bit map writable character storage area are set to

640 KB and 192 KB, respectively.

(PC save area: 896 KB - 640KB - 192 KB = 64 KB)

[ESC] XF; 10, 03, 00 [LF] [NUL]

«
...
194
195
196
197
198
...
»

Summary of Contents for B-SX4T Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for B-SX4T Series

Brand: xpr Pages: 10

Brand: Aopos Pages: 70

Brand: Fametech Pages: 50

Brand: Barnes & Noble Pages: 14

Brand: Globalcom Pages: 24

Brand: Cognex Pages: 17

Brand: Farpointe Data Pages: 2

Brand: Anker Pages: 14

Brand: Hama Pages: 24

Brand: IDTECH Pages: 37

Traveldrive 1000&1

Brand: Hama Pages: 22

Brand: IDTECK Pages: 20

Brand: IDTECH Pages: 19

Brand: IDTECH Pages: 23

Brand: IDENTEC SOLUTIONS Pages: 55

Brand: ViewSonic Pages: 2

Brand: Banner Pages: 17

Brand: TSC Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands