Toshiba B-SX4T Series Page 36 Specification Download

Page: 36 / 374

- 32 -

5.2 LABEL ISSUE OPERATION

An example of the label issue operation is described below.

(1) Where the Saved Data Call Command is not used:

NOTES:

(1) When placing new paper, the Label Size Set Command and the Feed Command must

always be sent. When using the same paper after the power is turned off and on, the
Label Size Set Command and the Feed Command may be omitted.

(2) After the power is turned off and on, the Bit Map Font Format Command, the Outline

Font Format Command, and the Bar Code Format Command should be sent as
occasion demands because they are not protected in memory.

Power ON

Bit Map Font Data Command

Yes

Position Fine Adjust Command

Print Density Fine

Adjust Command

Image Buffer Clear Command

Line Format Command

Bit Map Font Format Command

Outline Font Format Command

Bar Code Format Command

[ESC] D: Sets the label size.

[ESC] AX: Adjusts the feed length, cut position, and

back feed length.

[ESC] AY: Adjusts the print density.

[ESC] C: Clears the image buffer.

[ESC] LC: Sets the line format and draws it.

[ESC] PC: Sets the bit map font format.

[ESC] PV: Sets the outline font format.

[ESC] XB: Sets the bar code format.

[ESC] RC: Draws bit map font data.

Feed Command

[ESC] T: Feeds one sheet of paper and aligns it

with the first print position.

Outline Font Data Command

[ESC] RV: Draws outline font data.

Bar Code Data Command

[ESC] RB: Draws bar code data.

Issue Command

[ESC] XS: Issues (prints) the label.

Yes

Yes

Power OFF

Label Size Set Command

Place paper

Summary of Contents for B-SX4T Series























































































































































































































































































































































































Search results

Summary of Contents for B-SX4T Series

Reviews:

Related manuals for B-SX4T Series

Brands by name

Popular brands

Toshiba B-SX4T Series, Specification

Search results

Summary of Contents for B-SX4T Series

Reviews:

Related manuals for B-SX4T Series

Brands by name

Popular brands