manualshive.com logo in svg

Toshiba B-SX4T Series, Specification

Share
Download
Toshiba B-SX4T Series Specification Download Page 121

 

- 117 -

 

Explanation 

(1)  The parameter, “Number of bytes to be read”, is effective only when RFID read 

mode is set to 1 or 3, as this parameter is intended for reading user data.    When 
reading tag ID, this parameter is ignored.   

 

 

(2)  When the value exceeding the maximum number of bytes storable in a tag is 

designated for “Number of bytes to be read”, a read error results.   

 

 

(3)  With RFID (data read) being specified by this command, when an RFID data read 

failed, the printer will retry to read data after sending a void pattern printing end 
status (60H) or result in an error and stop after sending an RFID write error status 
(61H).  

SOH 01H 

STX 02H 

Indicates the start of the status block 

34H 

Status 

32H 

Printer status 

Status type 

34H 

Indicates the end of an RFID read and issue. 

3XH 
3XH 
3XH 

Remaining 

count 

3XH 

Remaining issue count 

XXH 

Tag type 

XXH 

30H30H: RFID read failed. 
31H31H: I-Code 
31H32H: Tag-it 
31H33H: C220 
31H34H: ISO15693 
31H35H: C210 
31H36H: C240 
31H37H: C320 
32H31H: EPC Class 0 
32H32H: EPC Class 1 
32H33H: ISO18000-6B 
32H34H: EPC Class 1 Generation 2 

XXH 

Length 

XXH 

RFID data length 

XXH 
XXH 

: 
: 

XXH 

RFID data 

XXH 

Tag ID + User data 

* Data to be read is different depending on the RFID 
read mode setting.   

ETX 03H 

EOT 04H 

CR 0DH 

LF 0AH 

Indicates the end of the status block. 

 

 

 

(4)  When an access password is designated using this command, writing data onto a 

tag cannot be performed if the access password registered in the tag differs from 
the access password designated.    However, reading data can be performed. 
(If the tag is the Hibiki tag and read lock is set, reading the tag is also disabled.) 

 

Summary of Contents for B-SX4T Series























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands