Toshiba B-SX4T Series Specification Download

Page: 280 / 374

- 276 -

LED Indication

No.

LCD Messages of

Upper line

(English)

POWER

ON LINE ERROR

Printer Status

Restoration

by the

[RESTART]

key

Yes/No

Acceptance

of Status

Request

Reset

Command

Yes/No

RFID WRITE ERROR

{

Writing data onto the RFID tag
continuously failed for the
maximum number of RFID write
retries.

Yes Yes

RFID ERROR

{

The printer cannot communicate
with the RFID module.

No Yes

INPUT PASSWORD

{

The printer is waiting for a
password to be entered.

No No

PASSWORD INVALID

{

Password entered was not
correct consecutively for
three times.

No No

RFID CONFIG ERR

{

B-SX704-RFID-U2-US-R
only
RFID module’s destination
code is not specified.

No No

NOTE 1:

When a command error is found in the command sent, 16 bytes of the command code of the

error command are displayed on the upper line of the LCD. (However, [LF] and [NUL] are
not displayed.)

[Example 1] [ESC] PC001; 0A00, 0300, 2, 2, A, 00, B [LF] [NUL]

Command error

LCD display

PC001;0A00,0300,
B-SX4T V1.0A

[Example 2] [ESC] T20 G30 [LF] [NUL]

Command error

LCD display

T20G30

B-SX4T V1.0A

[Example 3] [ESC] XR; 0200, 0300, 0450, 1200, 1 [LF] [NUL]

Command error

LCD display

XR;0200,0300,045
B-SX4T V1.0A

NOTE 2:

When the command error is displayed, “? (3FH)” is displayed for codes other than 20H to 7FH

and A0H to DFH.

Summary of Contents for B-SX4T Series























































































































































































































































































































































































Search results

Summary of Contents for B-SX4T Series

Reviews:

Related manuals for B-SX4T Series

Brands by name

Popular brands

Toshiba B-SX4T Series, Specification

Search results

Summary of Contents for B-SX4T Series

Reviews:

Related manuals for B-SX4T Series

Brands by name

Popular brands