Thermo Scientific Cryofuge 5500i GMP Instructions For Use Manual Download Page 44

Page: 44 / 114

Rotors and accessories

Checking of aerosol-tight bio-containment

The checking of the rotor type and bucket was done

according to the dynamic microbiological test proce-

dure with regard to EN 61010-2-020 appendix AA.
The aerosol-tight bio-containment of the rotor mainly

depends on proper handling!

Close the bucket or rotor according to the respec-

tive handling instructions.
Shaking the bucket releases the carbon dioxide

of the water, and an excessive pressure is built

up.
Leaks are recognized by humidity release and

audible disinflation of gas mix.
Finally buckets respectively rotor, lid and lid seal

have to be dried.

It is very important, that all the seals and

seal-surfaces are being tested for wear

and damages like cracks, scratches and

embrittlement carefully!

As a quick test there is the possibility to check the

aerosol-tight buckets and fixed angle rotors according

to the following procedure:

grease slightly all seals.
Fill the bucket or rotor with approx. 50 ml carbon

dioxide mineral water.

Check the aerosol-tight bio-contain-

ment of your rotor whenever

necessary!

The construction of BIOshield

- and

Highplate

- rotors does not allow a

quick test according to this procedure

by the user; therefore a very careful

control of seals, seal surfaces and

lids is necessary!

Summary of Contents for Cryofuge 5500i GMP



















































































































Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands

Thermo Scientific Cryofuge 5500i GMP, Instructions For Use Manual

Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands