Thermo Scientific Cryofuge 5500i GMP Instructions For Use Manual Download Page 2

Page: 2 / 114

How to use this manual

Please, use this manual to get acquainted

with your centrifuge and its accessories.

The manual helps you to avoid inappropriate handling.

Make sure to always keep it close to the centrifuge.

A manual that is not kept handy cannot provide aid

against improper handling and thus against dam-

age to individuals and surrounding.

The manual contains chapters on

Safety regulations

Instrument description

Transport and installation of the centrifuge

Rotors and accessories

Use of the centrifuge

Maintenance and care

Troubleshooting

Technical data

Index

Overleaf you will find a graphical

illustration of the control panel and a

survey of the most important functions

Unfold, please

Summary of Contents for Cryofuge 5500i GMP



















































































































Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands

Thermo Scientific Cryofuge 5500i GMP, Instructions For Use Manual

Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands