Thermo Scientific Cryofuge 5500i GMP Instructions For Use Manual Download Page 48

Page: 48 / 114

Operation

Check carefully whether your tubes

are approved for the respective

RCF value. If not, reduce speed.

Filling the centrifuge tubes

For common borosilicate glass tubes, the maximum

permissible RCF is limited to 4000 x g!
The tube manufacturers normally limit the respective

maximum permissible RCF value to the fixed angle

rotor.

Maximum permissible load difference

The smaller the imbalance of the centri-

fuge

the better the separation effect, be-

cause there are no turbulences in the

separated zones caused by vibrations.

Therefore it is important, that the tubes are balanced

properly.
The permissible load difference depends on many

factors (e.g. rotor, loading). For the swinging bucket

rotors LH-4000 and LH-4000W this difference

amounts to at least 30 g in opposite carriers.

Please note that for the same RCF value

the stress for the tubes in a swinging-

bucket rotor is higher!

Because of the higher difference of the

radii (r

max

- r

min

) the pressure of the liquid column to

the tube bottom is considerably higher and strongly

depended on filling.
Plastic tubes – especially for the highest load (speed,

temperature) – have a limited service life only and

must be replaced. For detailed questions please

contact the manufacturer of the plastic tubes.

Summary of Contents for Cryofuge 5500i GMP



















































































































Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands

Thermo Scientific Cryofuge 5500i GMP, Instructions For Use Manual

Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands