Thermo Scientific Cryofuge 5500i GMP Instructions For Use Manual Download Page 17

Page: 17 / 114

Before the use

The setting up and connecting of the

Cryofuge 5500i GMP may be imple-

mented exclusively by trained special-

ist personnel only!

Before the use

Setting up and connecting the centrifuge

The correct installation locations

The utilization of the centrifuge has to be implemented

in interior compartments. The installation locations

must meet these requirements:

A security area of at least 30 cm must be kept

around the centrifuge. No dangerous materials may

be located there during the centrifugation.
The floor must be stable and resonance-free.
The centrifuge must be protected against heat and

strong solar radiation.

Transporting centrifuge

UV radiation reduce the durability of

plastics.
Place the centrifuge, as well as ro-

tors and accessories of plastic, so

that they are not exposed to direct

solar radiation!

The centrifuge can be damaged

during transport through shock

impacts!
Transport the centrifuge in the

upright position, without rotor and

only in the corresponding special

packing.
Ensure sufficient protection!

Summary of Contents for Cryofuge 5500i GMP



















































































































Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands

Thermo Scientific Cryofuge 5500i GMP, Instructions For Use Manual

Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands