Thermo Scientific Cryofuge 5500i GMP Instructions For Use Manual Download Page 77

Page: 77 / 114

Troubleshooting

Error message

Symptoms

Possible causes and corrective measures

E-06

Rotor stops without de-

celeration to standstill.

Instrument cannot be

operated.

Communication error between key panel and CPU

Switch the instrument off and on again. If the error persists, con-

tact customer service.

E-07

The rotor is decelerated

to a standstill. The lid can

be opened.

Over temperature in the centrifuge chamber

Display > 51

°C or measured temperature > 70

°C.

(Cooling machine possibly defective.)

E-08

Rotor stops without de-

celeration to standstill.

Instrument cannot be

operated.

Over voltage at frequency converter

Mains voltage outside the tolerance. Deceleration resistance de-

fective. If necessary, request customer service.

E-10

Self-test after switching

on the centrifuge.

NV-RAM; error in program memory

Switch the instrument off and on again. If the error persists, con-

tact customers service.

E-12

Rotor stops without de-

celeration to standstill.

Instrument cannot be

operated.

Temperature measurement error.

Switch the instrument off and on again. If the error persists, con-

tact customer service.

Summary of Contents for Cryofuge 5500i GMP



















































































































Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands

Thermo Scientific Cryofuge 5500i GMP, Instructions For Use Manual

Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands