Thermo Scientific Cryofuge 5500i GMP Instructions For Use Manual Download Page 62

Page: 62 / 114

Operation

Centrifuging with a program

After closing the centrifuge lid, recall the

desired program memory number using

the program selection key and actuate the

start key

If the rotor is started with a program the speed or

RCF set value of which exceeds the permissible one

for the inserted rotor or the RCF/set value of which is

below the rotor-specific minimum, the display in the

program display section is changed to [ ] after the

identification of the rotor.

“Quick Run”

For short-term operation, the

Cryofuge

5500i GMP

equipped with a “Quick Run” function

Short-term centrifugation is started by pressing the

“quick run” key

continuously; it stops as soon as

the key is released.
In this mode the centrifuge accelerates and deceler-

ates with full power. The set speed or RCF is ignored

in this case.

During acceleration the time is counted forward in

seconds. The display stays until the centrifuge lid is

opened.

Depending on the rotor installed, the

centrifuge accelerates to the maxi-

mum speed!
Check carefully whether you have

to maintain a specific speed limit

for your application.

Summary of Contents for Cryofuge 5500i GMP



















































































































Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands

Thermo Scientific Cryofuge 5500i GMP, Instructions For Use Manual

Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands