Thermo Scientific Cryofuge 5500i GMP Instructions For Use Manual Download Page 59

Page: 59 / 114

Operation

Starting the centrifuge

Once the rotor has been properly installed, the main

switch turned on and the lid closed, you can start the

centrifuge.
Press the “start” key

in the control panel. The cen-

trifuge accelerates to the selected value. Simultane-

ously time display starts counting down in sec. incre-

ments (during continuous operation the time display

goes forward).
If a value exceeding the maximum permissible speed

or RCF of the respective rotor was entered, this is

indicated after the start of the centrifuge by the alter-

nately flashing messages “rotor” and the maximum

permissible value for the inserted rotor.
Within 15 seconds you may adopt this value by again

actuating the “start” key repeatedly; the centrifugation

is then continued. Otherwise the centrifuge stops, and

you must enter a permissible value.
You cannot open the lid during the run.

Imbalance display

If an imbalanced load exists, this will be displayed

above a speed of approximately 300 rpm through the

hint “bAL” in the speed display.

The run is terminated,

and you may restart the

centrifuge after having

corrected the imbalance

(check loading).

Changing the settings during the run

You can change all settings during a run. By pressing

once any of the “set” keys in the control panel you

can switch from the actual to the set value mode.
The setting to be adjusted flashes and can then be

altered. Once the data input has been completed and

the display has changed to the actual value mode, the

new settings become operative.

Summary of Contents for Cryofuge 5500i GMP



















































































































Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands

Thermo Scientific Cryofuge 5500i GMP, Instructions For Use Manual

Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands