Thermo Scientific Cryofuge 5500i GMP Instructions For Use Manual Download Page 41

Page: 41 / 114

Rotors and accessories

BIOshield

-Rotor 75006435

Highplate

-Rotor 75006444

Closing round buckets aerosol-tightly

After greasing the seal, turn the lid until it fits slightly

to the bucket.
To achieve an uniform pre-stressing, turn the lid

clockwise by 1 ½ grip areas ( approx. 15°). Use the

setting marks on the bucket as an orientation.

If the windshield-rotors are filled with samples outside

the centrifuge (e.g. in a safety work bench), it is es-

sential that during the insertion into the centrifuge the

rotor is kept in a vertical position.

Grip areas

Bucket mark

The aerosol-tight bio-containment of

windshield-rotors is only secured in a

horizontal position!

Summary of Contents for Cryofuge 5500i GMP



















































































































Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands

Thermo Scientific Cryofuge 5500i GMP, Instructions For Use Manual

Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands