Thermo Scientific Cryofuge 5500i GMP Instructions For Use Manual Download Page 71

Page: 71 / 114

Troubleshooting

Troubleshooting

Emergency lid release

In case of a power failure the lid cannot be opened

using the electrical lid release

To permit unloading in

this case, the centrifuge is equipped with an emer-

gency lid release. However, you may use this system

in case of emergency only.

Proceed as follows:
1. Make sure the rotor is at a standstill

(sight glass in the lid).

2. Pull mains plug.
3. On the right- and left-hand side of the front screen

there is a plastic plug, which you can remove with

a screwdriver or a knife.

Emergency release

Rotor can run at high speed! Touch-

ing it may cause severe injuries

Always wait several minutes until

the rotor has come to a complete

standstill without deceleration.

Without power supply the brake is

out of operation, and deceleration

takes much longer than normal!

During a power failure it is impossible

to lock the lid once the emergency lid

release has been actuated

Never decelerate the rotor using your

hands or tools

Summary of Contents for Cryofuge 5500i GMP



















































































































Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands

Thermo Scientific Cryofuge 5500i GMP, Instructions For Use Manual

Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands