Thermo Scientific Cryofuge 5500i GMP Instructions For Use Manual Download Page 45

Page: 45 / 114

Operation

Operation

Switching on the centrifuge

Locate the mains switch on the right-hand side of the

front panel.
For a short time, the following reading appears in the

control panel:

The display shows that the instrument is going

through an internal check of its software (see table on

page 77).
After this check, the display changes into the actual

value mode. The remaining run time and speed

should both read “0”. The display of the accelera-

tion/deceleration curve depends on the last set value.
The following figure gives an example of possible

readings. A detailed description of possible settings is

given below in this chapter.

Actuating the lid

Opening the lid

Press the “open lid” key .
If the message “Lift lid” appears, you must lift the lid

slightly.
(Emergency release in case of malfunction or power

failure: see chapter “Troubleshooting”)

Closing the lid

The centrifuge lid is locked by slightly pressing down

the front part of the lid. Locking is motor-driven.

Do not slam the lid!

Summary of Contents for Cryofuge 5500i GMP



















































































































Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands

Thermo Scientific Cryofuge 5500i GMP, Instructions For Use Manual

Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands