Thermo Scientific Cryofuge 5500i GMP Instructions For Use Manual Download Page 60

Page: 60 / 114

Operation

Stopping the centrifuge

At limited run time

Normally the run time has been set manually and all

you have to do is wait until the centrifuge terminates

the run automatically at the end of the set time.
As soon as the speed reaches zero, the display reads

“end”. You can now open the centrifuge by pressing

the “open lid” key

and remove the centrifuged

material.
If the lid has not been fully lifted out of the lid lock, the

message “lift lid” appears (manual lift of the lid is nec-

essary).
You can manually stop the centrifuge at any time by

actuating the “stop” key .
At this point the remaining run time is displayed.

At continuous operation

If you have chosen continuous operation, you must

stop the centrifuge manually. Press the “stop” key

in the control panel. The centrifuge will be deceler-

ated with the preset deceleration profile.
The display reads “end”, and you can open the lid by

pressing the “open lid” key

and remove the centri-

fuged material.

Temperature control during standby

The exact regulation will be active after identification

of the rotor. This is the case after a centrifugation run

exceeding 300 rpm. At standby the speed display

reads “end”.
If the rotor has not been identified (lid has been

closed and the “start” key

has not yet been actu-

ated, speed display shows “0” with flashing point), the

temperature regulation inhibits the freezing of the

sample only. An exact regulation cannot be guaran-

teed.

Summary of Contents for Cryofuge 5500i GMP



















































































































Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands

Thermo Scientific Cryofuge 5500i GMP, Instructions For Use Manual

Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands