Thermo Scientific Cryofuge 5500i GMP Instructions For Use Manual Download Page 80

Page: 80 / 114

Troubleshooting

Error message

Symptoms

Possible causes and corrective measures

E-25

Rotor stops without de-

celeration to standstill.

Start without rotor, or improper rotor fastening.

1. Switch the instrument off and on again.
2. Open the centrifuge by pressing the “lid open”-key .,
3. Check, whether the rotor has been inserted and fastened cor-

rectly.

If the error persists, contact customer service.

E-27

Rotor stops without de-

celeration to standstill.

Instrument cannot be

operated.

Mains voltage too low.

Electronics overheated.

1. Turn instrument off and pull mains plug.

2. Check and clean ventilation slots if necessary.

3. After about 60 min you can restart the instrument.
If the error persists, contact customer service.

Summary of Contents for Cryofuge 5500i GMP



















































































































Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands

Thermo Scientific Cryofuge 5500i GMP, Instructions For Use Manual

Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands