Thermo Scientific Cryofuge 5500i GMP Instructions For Use Manual Download Page 75

Page: 75 / 114

Troubleshooting

Error message

Symptoms

Possible causes and corrective measures

Message “rotor

”

appears in dis-

play.

Rotor decelerates with

delayed deceleration.

Set speed exceeds permissible maximum speed for the rotor.

(The same holds for RCF setting)

A) For approx. 15 sec. the maximum permissible rotor speed or

rcf for the inserted rotor will be shown alternately by “rotor” in

the display Within this period, it is possible to accept this value

by again pressing the “start” key. The centrifugation is then

continued.

B) Following onset of deceleration, you must wait until the rotor

has stopped. By opening and closing the lid you reset the mes-

sage “rotor”. After entering a permissible speed, you can start

again.

Display “OPEN”

appears al-

though lid is

closed

Will not start.

Lid not properly closed

Open the lid and repeat locking procedure.

Message “Lid

”

appears in the

display.

Drive stops.

Rotor stops without de-

celeration to standstill.

Lid was opened manually during the run.

1. Press the lid again shut. The instrument stops without decel-

eration.

2. If you want to continue the run, you must switch the instrument

off and on again.

Summary of Contents for Cryofuge 5500i GMP



















































































































Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands

Thermo Scientific Cryofuge 5500i GMP, Instructions For Use Manual

Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands