manualshive.com logo in svg

Thermo Scientific Applied Biosystems SeqStudio Genetic Analyzer, User Manual

The Thermo Scientific Applied Biosystems SeqStudio Genetic Analyzer is a cutting-edge genetic analysis system designed to deliver accurate and reliable results. To help users get started, we provide an informative "Getting Started Manual" that you can easily download for free from our website. Explore the possibilities of genetic analysis with confidence.

Share
Download
background image

Device

Description

Uninterruptible

power supply

(UPS)

We recommend the use of a 1.5-kVA uninterruptible power supply (UPS), especially in areas

prone to power failure. Power failures and other events that abruptly terminate the function of

the instrument and computer can corrupt data and possibly damage the system.

WARNING! 

PHYSICAL INJURY HAZARD. Do not attempt to lift the UPS unit without

assistance of at least two people. Improper lifting can cause painful and permanent back

injury. Refer to the UPS manufacturer user guide for more information.

IMPORTANT! 

UPSs provide power for a limited time. They are meant to delay the effects of a

power outage, not to serve as replacement power sources. In the event of a power loss, power

off the instrument and computer unless you expect to regain power within the battery life of the

UPS.

Surge protector

We recommend the use of a 10-kVA surge protector (line conditioner) in areas with frequent

electrical storms or near devices that are electrically noisy, such as refrigerators, air

conditioners, or centrifuges. Short-duration, high-voltage power fluctuations can abruptly

terminate the function of, and thereby damage the components of, the computer and the

instrument.

Note: 

A dedicated line and ground between the instrument, computer, and the building’s main

electrical service can also prevent problems caused by power fluctuations.

Network requirements

The instrument is factory-configured for IPv4 TCP/IP communication and includes a

fast Ethernet adapter (10/100 Mbps) with a RJ45-type connector for integrating the

device into a local area network (LAN). If the instrument will be connected to a LAN,

an active, tested network jack must be in place before the scheduled installation date.

Also, a representative from your information technologies department must complete

and return the SeqStudio

™

 Genetic Analyzer IT Checklist (Pub. No. MAN0016055) before

installation, and be available during the installation to help connect the instrument to

your network.

Safety requirements

A safety representative from your facility must ensure that:

• Personnel establish and follow all applicable safety practices and policies to

protect laboratory personnel from potential hazards.

• All applicable safety devices and equipment are available at all times.

Safety practices

Appendix G 

Instrument specifications and layout

Network requirements

G

SeqStudio

™

 Genetic Analyzer Instrument and Software User Guide

225

Summary of Contents for Applied Biosystems SeqStudio Genetic Analyzer



















































































































































































































































Reviews:

No comments

Related manuals for Applied Biosystems SeqStudio Genetic Analyzer

Oakton 700 Series Quick Manual preview
700 Series
Brand: Oakton Pages: 4
Bacharach MGS-401 User Manual preview
MGS-401
Brand: Bacharach Pages: 19
Hach Ultra ORBISPHERE 3624 Operator'S Quick Manual preview
ORBISPHERE 3624
Brand: Hach Ultra Pages: 12
Wavetek MS1000 Operation Manual preview
MS1000
Brand: Wavetek Pages: 43
UFM CoolPoint CP12-V8 Installation And Operation Manual preview
CoolPoint CP12-V8
Brand: UFM Pages: 14
TDI Nitro-Save NS16 Operating Instructions preview
Nitro-Save NS16
Brand: TDI Pages: 4
Sensitech FreezeAlert Instructions For Use preview
FreezeAlert
Brand: Sensitech Pages: 2
Korg OASYS CX-3 Manuald Tour preview
OASYS CX-3
Brand: Korg Pages: 4
Tenma 72-14400 User Manual preview
72-14400
Brand: Tenma Pages: 7
iDigit A570 Ambient Monitor Instruction Manual preview
A570 Ambient Monitor
Brand: iDigit Pages: 15
Ametek LG-002 User Manual preview
LG-002
Brand: Ametek Pages: 7
Fora ATMS Training Manual preview
ATMS
Brand: Fora Pages: 10
Keithley 6482 Reference Manual preview
6482
Brand: Keithley Pages: 350
Lovibond Tintometer XD 7500 Quick Start Manual preview
Tintometer XD 7500
Brand: Lovibond Pages: 164
Underground Magnetics Mag 8e Manual preview
Mag 8e
Brand: Underground Magnetics Pages: 53
AccuFitness FatTrack II User Manual preview
FatTrack II
Brand: AccuFitness Pages: 2
ENMET ISA-40 Series Manual preview
ISA-40 Series
Brand: ENMET Pages: 19
Benstone Fieldpaq User Manual preview
Fieldpaq
Brand: Benstone Pages: 222

Brands by name

Popular brands

Load more brands