Home
/
Texas Instruments
/
TMS320VC5509
/
Reference Manual

Texas Instruments TMS320VC5509, Reference Manual, Page: 250 / 285

Share

Page: 250 / 285

Texas Instruments TMS320VC5509 Reference Manual Download Page 250

Pin Control Register (PCR)

12-43

McBSP Registers

SPRU592E

11.PCR Bit Descriptions (Continued)

Bit

Field

Value

Description

8

CLKRM

Receive clock mode bit. The role of CLKRM and the resulting effect on the
CLKR pin depend on whether the McBSP is in the digital loopback mode
(DLB = 1).

Note:

The polarity of the signal on the CLKR pin is determined by the

CLKRP bit.

NOT in digital loopback mode (DLB = 0):

0

The CLKR pin is an input pin that supplies the internal receive clock (CLKR).

1

Internal CLKR is driven by the sample rate generator of the McBSP. The
CLKR pin is an output pin that reflects internal CLKR.

In digital loopback mode (DLB = 1):

0

The CLKR pin is in the

high impedance state

. The internal receive clock

(CLKR) is driven by the internal transmit clock (CLKX). CLKX is derived
according to the CLKXM bit.

1

Internal CLKR is driven by internal CLKX. The CLKR pin is an output pin that
reflects internal CLKR. CLKX is derived according to the CLKXM bit.

«
...
248
249
250
251
252
...
»

Summary of Contents for TMS320VC5509






























































































































































































































































































Reviews:

No comments