manualshive.com logo in svg

Texas Instruments TMS320VC5509, Reference Manual, Page: 247 / 285

Share
Download
Texas Instruments TMS320VC5509 Reference Manual Download Page 247

Pin Control Register (PCR)

McBSP Registers

12-40

SPRU592E

Table 12

−

11. PCR Bit Descriptions (Continued)

Bit

Description

Value

Field

12

RIOEN

Receive I/O enable bit. When the receiver is in reset (RRST = 0), RIOEN
can configure certain McBSP pins as general-purpose I/O (GPIO) pins . For
a summary, see the table that follows the RIOEN bit description. XRST and
RRST are in the serial port control registers, but all other bits mentioned in
this table are in the pin control register.

0

The CLKR, FSR, DR, and CLKS pins are serial port pins.

1

If RRST = 0, the CLKR, FSR, and DR pins are GPIO pins. The CLKS is also
a GPIO pin if XRST = 0 and XIOEN = 1.

Pin

General Purpose Use
Enabled by This Bit
Combination

Selected as
Output When 

…

Output Value
Driven From
This Bit

Selected As
Input When 

…

Input Value
Read From
This Bit

CLKX

XRST = 0
XIOEN = 1

CLKXM = 1

CLKXP

CLKXM = 0

CLKXP

FSX

XRST = 0
XIOEN = 1

FSXM = 1

FSXP

FSXM = 0

FSXP

DX

XRST = 0
XIOEN = 1

Always

DXSTAT

Never

Does not apply

CLKR

RRST = 0
RIOEN = 1

CLKRM = 1

CLKRP

CLKRM = 0

CLKRP

FSR

RRST = 0
RIOEN = 1

FSRM = 1

FSRP

FSRM = 0

FSRP

DR

RRST = 0
RIOEN = 1

Never

Does not apply

Always

DRSTAT

CLKS

RRST = XRST = 0
RIOEN = XIOEN = 1

Never

Does not apply

Always

CLKSSTAT

Summary of Contents for TMS320VC5509






























































































































































































































































































Reviews:

No comments