Texas Instruments TMS320VC5509 Reference Manual Download Page 183

Page: 183 / 285

Setting the SRG Clock Synchronization Mode

Transmitter Configuration

8-36

SPRU592E

8.22 Setting the SRG Clock Synchronization Mode

The GSYNC bit (see Figure 8

−

26 and Table 8

−

25) determines the SRG clock

synchronization mode.

Figure 8

−

26. Register Bit Used to Set the SRG Clock Synchronization Mode

SRGR2

GSYNC

R/W-0

Legend:

R = Read; W = Write; -

= Value after reset

Table 8

−

25. Register Bit Used to Set the SRG Clock Synchronization Mode

Register

Bit

Name

Function

SRGR2

GSYNC

†

Sample Rate Generator Clock Synchronization
GSYNC is used only when the input clock source for the sample rate
generator is external on the CLKS or CLKR pin.

GSYNC = 0

The sample rate generator clock (CLKG) is free running.
CLKG oscillates without adjustment, and FSG pulses
every (FPER + 1) CLKG cycles.

GSYNC = 1

Clock synchronization is performed. When a pulse is
detected on the FSR pin:

CLKG is adjusted as necessary so that it is
synchronized with the input clock on the CLKS or
CLKR pin.

FSG pulses.
FSG pulses

only

in response to a pulse on the FSR

pin. The frame-sync period defined in FPER is
ignored.

†

The clock synchronization provided through the GSYNC bit is not supported on TMS320VC5501 and TMS320VC5502
devices.

Summary of Contents for TMS320VC5509



















































































































































































































































































Search results

Summary of Contents for TMS320VC5509

Reviews:

Related manuals for TMS320VC5509

Brands by name

Popular brands

Texas Instruments TMS320VC5509, Reference Manual

Search results

Summary of Contents for TMS320VC5509

Reviews:

Related manuals for TMS320VC5509

Brands by name

Popular brands