Texas Instruments TMS320VC5509 Reference Manual Download Page 143

Page: 143 / 285

Setting the SRG Clock Divide-Down Value

Receiver Configuration

7-38

SPRU592E

Note:

The maximum frequency for the McBSP on the TMS320VC5503/5507/5509

and TMS320VC5510 devices is 1/2 the CPU clock frequency. The maximum

frequency for the McBSP on the TMS320VC5501 and TMS320VC5502

devices is 1/2 the frequency of the slow peripherals clock. For more

information on programming the frequency of the slow peripheral clock, see

the

TMS320VC5501 Fixed-Point Digital Signal Processor Data Manual

(literature number SPRS206) or the

TMS320VC5502 Fixed-Point Digital

Signal Processor Data Manual

(literature number SPRS166). Other timing

limitations may also apply. Refer to the device-specific data manual for

detailed information on the McBSP timing requirements.
When driving CLKX or CLKR at the pin, choose an appropriate input clock

frequency. When using the internal sample rate generator for CLKX and/or

CLKR, choose an appropriate input clock frequency and divide down value

(CLKGDV).

Summary of Contents for TMS320VC5509



















































































































































































































































































Search results

Summary of Contents for TMS320VC5509

Reviews:

Related manuals for TMS320VC5509

Brands by name

Popular brands

Texas Instruments TMS320VC5509, Reference Manual

Search results

Summary of Contents for TMS320VC5509

Reviews:

Related manuals for TMS320VC5509

Brands by name

Popular brands