tatsuno OCEAN TOWER Series, Installation And User Manual

Page: 166 / 173

TATSUNO EUROPE a.s., www.tatsuno ‐ europe.com
166
Code of
message
Type of
message
Cause of
error message
Removing
error message
E31 NFAT
Pulse generator channel error
at input PDEX5 ‐ PUL1 (PDEX ‐ 1A)
Raise and hang up the delivery nozzle several times.
Turn the power supply of the dispenser off and on.
If the fault persists, call an authorized service centre.
E32 NFAT
Pulse generator channel error
at input PDEX5 – PUL2 (PDEX ‐ 2A)
E33 NFAT
Pulse generator channel error
at input PDEX5 – PUL3 (PDEX ‐ 3A)
E34 NFAT
Pulse generator channel error
at input PDEX5 – PUL4 (PDEX ‐ 4A)
E35 NFAT
Pulse generator channel error
at input PDEX5 – PUL5 (PDEX ‐ 5A/1B)
E36 NFAT
Pulse generator channel error
at input PDEX5 – PUL6 (PDEX ‐ 6A/2B)
E37 NFAT
Pulse generator channel error
at input PDEX5 – PUL7 (PDEX – 7A/3B)
E38 NFAT
Pulse generator channel error
at input PDEX5 – PUL8 (PDEX ‐ 8A/4B)
E39 NFAT
Pulse generator channel error
at input PDEX5 – PUL9
E40 NFAT
Pulse generator channel error
at input PDEX5 – PUL10
E41 NFAT
Connection error or internal pulse generator error
at input PDEX5 ‐ PUL1 (PDEX ‐ 1A)
Raise and hang up the delivery nozzle several times.
Turn the power supply of the dispenser off and on.
If the fault persists, call an authorized service centre.
E42 NFAT
Connection error or internal pulse generator error
at input PDEX5 – PUL2 (PDEX ‐ 2A)
E43 NFAT
Connection error or internal pulse generator error
at input PDEX5 – PUL3 (PDEX ‐ 3A)
E44 NFAT
Connection error or internal pulse generator error
at input PDEX5 – PUL4 (PDEX ‐ 4A)
E45 NFAT
Connection error or internal pulse generator error
at input PDEX5 – PUL5 (PDEX ‐ 5A/1B)
E46 NFAT
Connection error or internal pulse generator error
at input PDEX5 – PUL6 (PDEX ‐ 6A/2B)
E47 NFAT
Connection error or internal pulse generator error
at input PDEX5 – PUL7 (PDEX – 7A/3B)
E48 NFAT
Connection error or internal pulse generator error
at input PDEX5 – PUL8 (PDEX ‐ 8A/4B)
E49 NFAT
Connection error or internal pulse generator error
at input PDEX5 – PUL9
E50 NFAT
Connection error or internal pulse generator error
at input PDEX5 – PUL10
E51 NFAT
Too much air in the petrol fuel or insufficient LPG pressure
difference
Petrol: The air flow sensor on the output of pump air
separator has been active for longer than specified by
parameter M10 ‐ P03.
LPG: The LPG pressure difference was less than 1 bar for
longer than specified by parameter M10 ‐ P03.
E51 ‐ 1 Main pump aeration or low pressure
LPG difference (between gas and liquid phase> 1bar)
E51 ‐ 2 Auxiliary pump aeration
Petrol: Check the intake manifold for leaks.
LPG: Check the pressure in the supply line and the
pressure in the return line of the gas phase discharge and
the permeability of the line.
Check the setting of the TRAFAG differential pressure
switch or on connected pressure sensors.
If the fault persists, call an authorized service centre.