SRT Thuraya Operating Instructions Manual Download Page 63

Page: 63 / 73

FCC Statements

FCC Part 15.19 Warning Statement- (Required for all Part 15

devices)

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS

SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY

NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST

ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT

MAY CAUSE UNDESIRED OPERATION.

FCC Part 15.21 Warning Statement

NOTE: THE

GRANTEE

IS NOT RESPONSIBLE FOR ANY CHANGES OR

MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY

RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID

THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

NOTE

: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

FCC Part 1.1310 & 2.1091 Rf Exposure Statement

To Satisfy FCC RF exposure requirements for mobile transmitting devices, a separation dis-

tance of

58 cm

or more should be maintained between the antenna of this device and per-

sons during device operation. To ensure compliance, operations at closer than this distance

is not recommended.
The antenna used for this transmitter must not be co-located in conjunction with any other

antenna or transmitter.

4. Agency Compliance Statements

Summary of Contents for Thuraya










































































Search results

Summary of Contents for Thuraya

Reviews:

Related manuals for Thuraya

Brands by name

Popular brands

SRT Thuraya, Operating Instructions Manual

Search results

Summary of Contents for Thuraya

Reviews:

Related manuals for Thuraya

Brands by name

Popular brands