manualshive.com logo in svg

SRT Thuraya, Operating Instructions Manual, Page: 25 / 73

Share
Download
SRT Thuraya Operating Instructions Manual Download Page 25

Install SIM Card

Your

Thuraya IP Commander

has two SIM card slots, one designated as

Secondary

and

the other as

Primary

. Both are installed into slots behind a metal plate on the left side of the

Thuraya IP Commander

enclosure, though only the

Primary

SIM card (right-hand slot)

is used at this time. Below are the instructions for installing the SIM card.

Figure 5: Steps to Install SIM Card

Item

Procedure

❶

Remove six screws

from access panel

See Figure 5. Using a cross-point screwdriver, remove the six screws holding the

side access panel in place.

❷

Remove access panel Remove panel and put in a safe place.

❸

Remove gasket if

necessary

If the gasket remains completely in place, don’t remove it. If it does come loose,

set aside.

❹

Install Primary

SIM card

With the access panel removed, there are three openings on the side of the

Thuraya IP Commander enclosure. The Primary SIM card goes into the far right-

hand slot (closest to the front of the unit), labeled Primary. The SIM card recept-

acle is spring-loaded. Push until you feel it lock into place. To remove, press until

you feel the card unlock, then remove.

Table 5: Open Access Panel and Install Voice and IP SIM Cards

Item

Procedure

❸

Replace gasket

See Figure 5. Carefully place gasket into the slot from which it was removed. Gas-

ket must be completely inside the slot with no overhang.

❷

Replace access panel Place the access panel over the area from which it was removed. Align the screw

holes in the panel with the ones on the enclosure.

❶

Insert and tighten

screws

Insert the screws into the appropriate holes. Tighten hand tight to ensure the plate

is properly aligned. Tighten the rest of the way down with a cross-point screw-

driver. Do not over-tighten!

Table 6: Close and Secure the Access Panel

9

2. Your New IP Commander System

Summary of Contents for Thuraya










































































Reviews:

No comments