SRT Thuraya Operating Instructions Manual Download Page 65

Page: 65 / 73

5. FAQs

You can always find the latest

FAQs

at the

SRT Wireless

website:

http://www.srtwireless.net/network-terminals/ip-commander-faqs/

On the first initial boot up, in what mode does the IP Commander power up?

The first time you power your system on, it will boot up in IP Standard Mode.

There are two SIM card slots, one designated as Primary and the other as Secondary. Do I use both

slots?

Only the Primary slot is used.

Where do I activate my SIM card?

It must be activated by an authorized Thuraya service provider. It allows both Voice and IP Data.

Are there yearly maintenance fees associated with the system?

No.

How am I billed?

In IP Standard Mode, you are billed by the megabyte. In Streaming Mode, you are billed by the minute.

Do I have to wait until all status indicator lights turn green to use the IP Commander?

Not all lights have to be green but you should wait for the following combination before using the IP Com-

mander:

• Sup-green (power supply is connected)

• On-green (IP Commander is powered on)

• Act-flashing red/off (activity on the satellite link)

• Sat-green (Satellite antenna status)

• GPS-green (GPS status)

• Ant-flash red/green or solid green is fine (show transmit antenna status)

• LAN-green if you’re connected to a network; off if not connected (local area network status)

What should my RSSI be in order to achieve optimal voice and data performance?

In order to achieve optimal voice and data performance you should have a RSSI range between -105

and -95.

Does it matter where the antenna is placed on top of the vehicle?

Antenna placement on the vehicle should ensure that the antenna has clear line-of-sight to the satellite.

Why do I need to change my connection profiles?

Profiles are changeable to reflect the data use plan that you purchased.

When is it okay to power up and power down the IP Commander?

The antenna cable carries DC power. Always power the IP Commander down prior to connecting or dis-

connecting the antenna cable from either the antenna or the IP Commander.

SRT Wireless LLC is the sole distributor of products for SR Technologies, Inc.

Summary of Contents for Thuraya










































































Search results

Summary of Contents for Thuraya

Reviews:

Related manuals for Thuraya

Brands by name

Popular brands

SRT Thuraya, Operating Instructions Manual

Search results

Summary of Contents for Thuraya

Reviews:

Related manuals for Thuraya

Brands by name

Popular brands