SRT Thuraya Operating Instructions Manual Download Page 71

Page: 71 / 73

Number

Short Name

Remedial solutions by SRT

308

Network detached

mobile

Verifying the settings on the web console.

Restart the BDU and try again.

If the problem persists, please contact your Service Provider.

309

GPRS not allowed

Verify the correct settings in the web console and contact your Service

Provider to activate authorised service.

310

Service not allowed

Verify the correct settings in the web console and contact your Service

Provider to activate authorised service.

311

Identity cannot be

derived

Network registration failure. The BDU will retry automatically.

If the problem persists, please contact your Service Provider.

312

Location area not

allowed

Network connection failure due to the terminal which is not allowed in

the location area.

Please contact your Service Provider.

313

Temporary registration

failure

Network registration failure. The BDU will retry automatically.

If the problem persists, please contact your Service Provider.

314

General registration

failure

Network registration failure. The BDU will retry automatically.

If the problem persists, please contact your Service Provider.

315

Registration retries

exhausted

Network re-connection failure. Restart the BDU if the problem persists.

401

Signal lost

Make sure no obstruction is blocking satellite signal and the ADU has

a clear sky view in the direction of the satellite.

If the problem persists, restart the BDU.

402

Pilot tracking

Make sure no obstruction is blocking satellite signal and the ADU has

a clear sky view in the direction of the satellite

403

No GPS

Make sure no obstruction is blocking satellite signal and no object is

placed over the ADU.

Wait for 5 minutes for the GPS position to be updated.

If the problem persists, restart the BDU.

404

Old GPS

A new GPS fix is obtained during the connection process, super-

seding the old fix. The terminal will reacquire the connection.

If the problem continues and the new connection cannot be re-estab-

lished, please contact your Service Provider.

501

LLC or SNDCP failure Network connection failure caused by LLC or SNDCP failure. Restart

the BDU.

If the problem persists, please contact your Service Provider.

6. Troubleshooting

Summary of Contents for Thuraya










































































Search results

Summary of Contents for Thuraya

Reviews:

Related manuals for Thuraya

Brands by name

Popular brands

SRT Thuraya, Operating Instructions Manual

Search results

Summary of Contents for Thuraya

Reviews:

Related manuals for Thuraya

Brands by name

Popular brands