SRT Thuraya Operating Instructions Manual Download Page 70

Page: 70 / 73

6. Troubleshooting

Number

Short Name

Remedial solutions by SRT

201

No SIM card in primary

slot

Verify that the SIM card is present inside the BDU’s SIM card slot.

SIM card may be inserted wrongly.

Remove SIM card and ensure it is inserted properly according to its ori-

ented symbol on the BDU font panel.

SIM Card contacts may be dirt.

Clean the SIM card contact with a dry cloth.

If the problem persists, replace the SIM card with a known good SIM

card otherwise please return the BDU to your Service Provider for ser-

vice.

202

No SIM card in sec-

ondary slot

203

SIM communication

problem

Power down the BDU and try again.

204

SIM Locked

The SIM card is locked. Enter the PUK to unlock the SIM card.

205

SIM Missing file

SIM card was incorrectly programmed with missing required field(s).

Please contact your Service Provider.

301

Illegal MS

The subscriber information is rejected or the SIM card is not producing

correct authentication information.

Please contact the Service Provider.

302

PLMN not allowed

Network connection failure due to PLMN which is not allowed.

Please contact your Service Provider.

303

Roaming not allowed You are using an authorised SIM card from a carrier that does not

have a roaming agreement with your Service Provider.

Please contact the Service Provider.

304

IMSI unknown HLR

The subscriber information is not recognized by the network.

Please contact your Service Provider

305

IMSI unknown VLR

The subscriber information is not on the network's roaming list..

Please contact your Service Provider

306

Service not supported Network connection failure due to service option which is not sup-

ported.

Please contact your Service Provider.

307

Service not subscribed Verify the correct settings in the web console and contact your Service

Provider to activate authorised service.

Summary of Contents for Thuraya










































































Search results

Summary of Contents for Thuraya

Reviews:

Related manuals for Thuraya

Brands by name

Popular brands

SRT Thuraya, Operating Instructions Manual

Search results

Summary of Contents for Thuraya

Reviews:

Related manuals for Thuraya

Brands by name

Popular brands