SRT Thuraya Operating Instructions Manual Download Page 69

Page: 69 / 73

Error Codes

These error codes are displayed on the

Thuraya

handset, which connects to the front panel

of the

IP Commander

device.

Number

Short Name

Remedial solutions by SRT

No error

No action required. The BDU is functioning properly.

Failed to read IMEI

The BDU failed to read the IMEI.

Please restart the BDU

If the problem persists, contact your service provider.

Illegal ME

This hardware is not accepted by the network.

IMEI not accepted

The network does not allow emergency calls from this IMEI.

101

Invalid antenna model Check the correct antenna unit with its label “Only for Atlas IP BDU”.

102

HPA disabled

The antenna tranmit is powered off.

Please restart the BDU.

103

HPA thermal alarm

The antenna transmitter has overheated.

It may power off to prevent hardware damage.

Please allow the system to cool down by powering off for a short time.

104

HPA fan fault

The fan inside the antenna has reported a problem. Please restart the

BDU.

If the problem persists, the antenna may need replacement.

105

HPA unknown fault

The antenna transmitter has reported an unknown error code.

If the problem persists, the antenna may need replacement.

106

ATB failure

Check the antenna cable connections are secured at both ADU and

BDU antenna ports.

107

Antenna com-

munication problem

Check the antenna cable connections are secured at both ADU and

BDU antenna ports.

Restart the BDU.

108

Calibration failure

Check the antenna cable connections are secured at both ADU and

BDU antenna ports.

Restart the BDU

6. Troubleshooting

Summary of Contents for Thuraya










































































Search results

Summary of Contents for Thuraya

Reviews:

Related manuals for Thuraya

Brands by name

Popular brands

SRT Thuraya, Operating Instructions Manual

Search results

Summary of Contents for Thuraya

Reviews:

Related manuals for Thuraya

Brands by name

Popular brands