Sony BVH-2000, Operation And Maintenance Manual

Page: 38 / 505

z
o
I-
«
a:
ill
Q..
o
@
STOP button
Pressing the STOP button stops all modes. The reel
motor stops and the pinch roller is retracted from the
tape.
• About 30 seconds after the STOP button has been
pressed, the tension release mechanism is operated
and the machine enters the STANDBY mode
(reduced tape tension). The TENSION OFF
ENABLE switch (S9-7) on the SY-79 board can be
turned OFF so that the tension release mechanism
does not operate.
• The machine goes into the STOP mode automatically
after the power is turned on or if the tape is out of
the tape sensor.
• The STOP lamp flashing shows that no reference
signal is being supplied to the servo system.
In the STOP or STANDBY if the tape is too
slack, the slack will be taken up automatically.
@
STANDBY button
This push off button is used to start the drum
rotating. In normal use, after the STANDBY button
has been pressed, the SERVO alarm lamp
G)
is checked
to see that it is off and then the desired mode button is
pressed. However, it is also possible to go into that
mode by pressing the desired button directly without
the STANDBY button having been pressed. When
about 9 minutes has without any button
being pressed after the STANDBY button has been
pressed, the STANDBY mode is released automatically.
the STANDBY OFF ENABLE switch (S9-8) on
the SY-79 board is OFF or if either the AUTO
MODE button or one of the channel preset button
is lit, automatic release of the STANDBY mode
does not operate.
• If the tape sticks when the head drum starts to rotate,
the tension release mechanism operates to slacken
the tape.
• The STANDBY lamp flashed to show that the head
drum is rotating abnormally for some reason, or is
not rotating at all.
@
PLA Y button
When the PLAY button is pressed, the PLAY and
STANDBY lamps light and the machine enters the
normal playback mode (normal speed in the forward
direction). To cancell, press the STOP, JOG, SHUTTLE,
VAR or PREROLL button.
I t is possible to select by the or PLAY
head by means of the HEAD selector
0
on the
BVH-2000(02).
If a slight compensation of the tape speed
is necessary for synchronizing two BVH series VTRs,
turn the SEARCH dial
@
clockwise (faster) or
counterclockwise the PLAY
button pressed. -The degree of compensation is
determined by the rotation angle, and the range is
within
±
15% of the normal speed (capstan override
the bu tton will return
the VTR to the normal speed.
@
REC (record) button
When the PLAY button is pressed keeping the REC
button pressed, both the REC and PLAY lamps light
and the machine enters the record mode. To release,
press either the STOP, JOG, SHUTTLE , VAR or
PREROLL button.
xecorcina is the head regardless
of the position of the HEAD selector
0.
• To monitor the simultaneous playback picture
during recording with the BVH-2000(02), set the
selector
CD
to TAPE.
• When the REC INHIBIT lamp
@
is on, the machine
enters the PLAY mode without recording.
When the REC TEST switch on the SY-79 board is
set to ON and the BVH-2000(00) is in the STOP
mode, the BVH-2000(00) enters the REC TEST
mode the REC button. (For details,
refer to page 1-74.)
@
REC INHIBIT lamp
This shows that the unit is in the REC
mode. This lamp lights when the REC INHIBIT switch
is set to ON, and the REC or REC EDIT mode is in-
hibited. recording or edit recording is
while this lamp is on, the machine will go into the
PLAY mode.
When the REC TEST switch on the SY-79 board is
set to ON and the is in the REC
TEST mode, the REC INHIBIT lamp blinks. (For
details, refer to page 1-74.)
@)
buttons
With another VTR connected to the REMOTE-2
connector on the rear panel and the REMOTE switch on
the SY -79 board set to set the
LOCAL switch on the level control panel to LOCAL
and the VTR works as a recorder. The following
controls can be performed by these buttons to
1-11-3.):
P button lights: When the P button is pressed and the
lamp lights, the editing and tape trans-
port buttons operate the connected
player, enabling remote control of the
player. The displays are also those of
the player. However, it is impossible to
operate the SERVO REF
0,
HEAD
0,
and TIME CODE/TIMER
®
selec-
tors and these selectors must be set at
the player side.
R button lights: When the R button is pressed and the
lamp lights, the buttons operate this
as a recorder. the AUTO MODE
button
@
is then pressed, the recorder
and the player go into the control
mode, enabling PREVIEW, AUTO
REVIEW to be performed.
1-28