Sony BVH-2000, Operation And Maintenance Manual

Page: 30 / 505

z
o
I-
«
a:
w
a..
o
@
REC button
When the PLAY button is keeping the
button pressed, both the REC and PLAY lamps light
and the machine enters the record mode. To release,
press either the STOP, JOG, SHUTTLE or PREROLL
button.
Recording is by the head regardless
of the position of the HEAD selector
0.
• To monitor the simultaneous playback picture
during recording on the BVH-2000(02), set the
T APE/EE selector
CD
to TAPE.
When the
@
is on, the machine
enters the PLAY mode without recording.
• When the REC TEST switch on the SY-79 board is
set to ON and the BVH-2000(00) is in the STOP
mode, the BVH-2000(00) enters the REC TEST
mode by the button.
refer to page 1-74.)
@
REC INHIBIT lamp
This lamp shows that the VTR is in the REC INHIBIT
mode. This lights when the REC INHIBIT switch
is set to ON, and REC mode is inhibited. If recording
attempted while this lamp is on, the machine will go
into the play mode.
• When the REC TEST switch on the SY -79 board is
set to ON and the BVH-2000(00) is in the
TEST mode, the REC lamp blinks.
details, refer to page 1-74.)
@
ENTRY button
This button is used to memorize the entry point. When
the ENTRY button is the desired
-nr'\C'11"11r'\?'\
the tape, this position is memorized. Even if the tape
is then run to another position, it can be returned to
the pre roll point (the position prior to the entry point
by the preroll time) by pressing the PREROLL button
@ ,
after which it stops. is for the
TIME CODE/TIMER-l/2 data which is displayed on
the display
®.
Therefore, in addition to the present
tape run point, it is possible to enter the input and
displayed data by means of the PRESET button
@ .
While the DISPLAY HOLD is lit, the ENTRY
point can be displayed pressing the ENTRY
button.
@
PREROLL button
If the PREROLL button is pressed, the tape returns to
the entry point preset by button then
stops at a position several seconds before the entry
point (preroll point).
The number of seconds of preroll can be set from 0 to
15 seconds on a one second basis using the P.ROL
switch on the SY-79 board.
If the READ switch on the BKH-2015 (TC-l is
set to VITC position and the TIME CODE/TIMER
selector
®
is set to TIME CODE, the preroll func-
tion does not work.
dial
This dial is used to change the tape run.
(1) By turning this dial during the JOG, SHUTTLE,
or PROGRAM JOG (refer to pages 1-21 and 22)
modes (refer to 1-9), it is possible to change the
direction and speed of the tape run.
this dial is turned during the
PLAY, or REC modes, the SEARCH indicator
lights, and it is possible to previously set the next
direction and speed of tape run in the PROGRAM
JOG mode.
When the SHUTTLE button is pressed, the lamp lights
and the machine enters the SHUTTLE mode. In this
state, if the SEARCH dial
@
is turned to either the
right or left and stopped at any position, will
be at the corresponding speed (1 to 50 times
normal). At the center position, the still picture is
obtained. The SEARCH dial clicks at the center
and ±50 positions.
• For fast winding in the forward the
winding speed is reduced automatically at the tape
end, and the unit stops automatically. If you wish
to wind the tape completely, turn the SEARCH dial
again to the right or set the EOT STOP switch on
the SY-80 board to OFF.
For fast winding the reverse direction
(rewmdmg),
the tape speed is reduced automatically at the tape
top and stops automatically near the TIMER-2
zero set position.
" you wish to rewind the tape completely, turn the
UA.J./. I..JI." ........... JI.
dial again to the left or set
switch on the SY-80 board to OFF.
• If the still mode is held for 3 minutes or more, the
machine enters the STOP mode automatically to
prevent damage to the tape. you don't want the
machine to stop, set the STILL
switch (S9-6) on the SY-79 board to OFF.
@
JOG button
When the JOG button is pressed, the lamp lights and
machine enters the mode. In this state, when
the dial is turned to either the left or right,
the playback speed depends on the speed of rotation
(0 to several times normal). When turning stops, the
picture will be still at that dial position. The SEARCH
dial does not click.
the STILL mode is held for 3 minutes or more,
the machine will go into the STOP mode automati-
cally. If you don't want the machine to stop, set the
STILL OFF ENABLE switch (S9-6) on the SY-79
board to OFF.
1-20