manualshive.com logo in svg

SMC Networks 8708L2, Management Manual

The SMC Networks 8708L2 is a cutting-edge networking device that delivers seamless connectivity. To ensure an effortless installation process, make use of the comprehensive Installation Manual available for free download on our website. Gain full control and unleash the potential of your network with this exceptional product.

Share
Download
background image

A

CCESS

 C

ONTROL

 L

IST

 C

OMMANDS

4-117

Access Control List Commands

Access Control Lists (ACL) provide packet filtering for IP frames (based 
on address, protocol, Layer 4 protocol port number or TCP control code) 
or any frames (based on MAC address or Ethernet type). To filter packets, 
first create an access list, add the required rules, specify a mask to modify 
the precedence in which the rules are checked, and then bind the list to a 
specific port. 

Access Control Lists

An ACL is a sequential list of permit or deny conditions that apply to IP 
addresses, MAC addresses, or other more specific criteria. This switch tests 
ingress or egress packets against the conditions in an ACL one by one. A 
packet will be accepted as soon as it matches a permit rule, or dropped as 
soon as it matches a deny rule. If no rules match for a list of all permit 
rules, the packet is dropped; and if no rules match for a list of all deny 
rules, the packet is accepted. 

There are three filtering modes: 

•

Standard IP ACL mode (STD-ACL) filters packets based on the source 
IP address. 

•

Extended IP ACL mode (EXT-ACL) filters packets based on source 
or destination IP address, as well as protocol type and protocol port 
number. If the TCP protocol is specified, then you can also filter 
packets based on the TCP control code. 

•

MAC ACL mode (MAC-ACL) filters packets based on the source or 
destination MAC address and the Ethernet frame type (RFC 1060).

The following restrictions apply to ACLs:

•

This switch supports ACLs for both ingress and egress filtering. 
However, you can only bind one IP ACL and one MAC ACL to any 
port for ingress filtering, and one IP ACL and one MAC ACL to any 
port for egress filtering. In other words, only four ACLs can be bound 

Summary of Contents for 8708L2































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8708L2

Panasonic BB-HGW700A - Network Camera Router Installation/Troubleshooting Manual preview
BB-HGW700A - Network Camera Router
Brand: Panasonic Pages: 10
JCG Q8 Quick Start Manual preview
Q8
Brand: JCG Pages: 2
Paradyne FrameSaver 9120 Installation Instruction Supplement preview
FrameSaver 9120
Brand: Paradyne Pages: 2
Delta Electronics DTE-20T Instruction Sheet preview
DTE-20T
Brand: Delta Electronics Pages: 1
TRENDnet TW-100 Specifications preview
TW-100
Brand: TRENDnet Pages: 2
Weidmuller IE-SW-VL16-14TX-2SC Hardware Installation Manual preview
IE-SW-VL16-14TX-2SC
Brand: Weidmuller Pages: 17
Ravpower RD-WD009 User Manual preview
RD-WD009
Brand: Ravpower Pages: 27
Buffalo LinkStation Mini User Manual preview
LinkStation Mini
Brand: Buffalo Pages: 71
LaCie 301297U - 1TB Ethernet Disk XP Embedded Network Attached... Online Manual preview
301297U - 1TB Ethernet Disk XP Embedded Network Attached...
Brand: LaCie Pages: 67
iGateWeb.com iGate User Manual preview
iGate
Brand: iGateWeb.com Pages: 6
Axis P3365-V Installation Manual preview
P3365-V
Brand: Axis Pages: 98
Comway 4G DTU Configuration Instructions preview
4G DTU
Brand: Comway Pages: 20
Solwise 3GWIFIMRD User Manual preview
3GWIFIMRD
Brand: Solwise Pages: 231
TP-Link Archer C7 How To Set Up preview
Archer C7
Brand: TP-Link Pages: 4
LevelOne NetCon FBR-1409TX User Manual preview
NetCon FBR-1409TX
Brand: LevelOne Pages: 88
Edimax GS-5208PLG V2 Quick Installation Manual preview
GS-5208PLG V2
Brand: Edimax Pages: 15
WTI NPS-16HD20-1 User Manual preview
NPS-16HD20-1
Brand: WTI Pages: 178
Asante IntraSwitch 5324MT Quick Installation Manual preview
IntraSwitch 5324MT
Brand: Asante Pages: 2

Brands by name

Popular brands

Load more brands