Silicon Laboratories Si5342 Family Reference Manual Download Page 99 | Manualshive

Page: 99 / 222

background image

Si5345-44-42-D-RM

Si5345

Rev. 1.0

99

See the settings and values from Table 26, “Settings for LVDS, LVPECL, and HCSL,” on page 42 for details of the
settings. ClockBuilder Pro is used to select the correct settings for this register.

Each output can be configured to use Multisynth N0-N4 divider. The frequency for each N-divider is set in registers
0x0302–0x0337 for N0 to N4. Five different frequencies can be set in the N-dividers (N0–N4) and each of the 10
outputs can be configured to any of the five different frequencies.

The 10 output drivers are all identical. The single set of descriptions above for output driver 0 applies to the other 9
output drivers.

Register 0x010A Output 0 Swing and Amplitude

Reg Address

Bit Field

Type

Name

Description

0x010A

3:0

R/W

OUT0_CM

This field only applies when OUT0_FORMAT=1 or 2.
See Table 26, “Settings for LVDS, LVPECL, and
HCSL,” on page 42 and " Appendix A—Setting the Dif-
ferential Output Driver to Non-Standard Amplitudes" on
page 219 for details of the settings.

0x010A

6:4

R/W

OUT0_AMPL

This field only applies when OUT0_FORMAT=1, 2, or
3. See Table 12, “Hitless Switching Enable Bit,” on
page 24 and “ Appendix A—Setting the Differential
Output Driver to Non-Standard Amplitudes” for details
of the settings.

Register 0x010B R-Divider 0 Mux Selection

Reg Address

Bit Field

Type

Name

Description

0x010B

2:0

R/W

OUT0_MUX_SEL

Output driver 0 input mux select.This
selects the source of the multisynth.
0: N0
1: N1
2: N2
3: N3
4: N4
5: reserved
6: reserved
7: reserved

0x010B

3

R/W

OUT0_VDD_SEL_EN

1 = Enable OUT0_VDD_SEL

0x010B

5:4

R/W

OUT0_VDD_SEL

Must be set to the VDD0 voltage.
3 = reserved, 2 = 3.3 V, 1 = 2.5 V, 0 = 1.8 V

0x010B

7:6

R/W

OUT0_INV

CLK and CLK not inverted
CLK inverted
CLK and CLK inverted
CLK inverted

«
...
97
98
99
100
101
...
»

Summary of Contents for Si5342































































































































































































































Reviews:

No comments

Related manuals for Si5342

Brand: Alcad Pages: 6

Brand: Maxim Pages: 14

Brand: Renesas Pages: 941

Enterasys Matrix 2G4082-25

Brand: Enterasys Pages: 58

Brand: Teletronics International Pages: 57

PCIe/PXIe-6301 Series

Brand: JYTEK Pages: 46

Brand: Idis Pages: 16

Brand: ZIMO Pages: 13

Brand: Pilz Pages: 12

MICROSPACE MSEBX800

Brand: DIGITAL-LOGIC Pages: 53

7798 I/SITE LAN

Brand: CSI Pages: 56

OG-HDTV-SDI-UHD

Brand: Opengear Pages: 7

Brand: PACOM Pages: 16

INTEL CORE i5 SYSTEM BOARD

Brand: Aprotech Pages: 154

EDID 101H 4K PLUS

Brand: Extron electronics Pages: 35

Brand: RadioLAN Pages: 118

EVAL-ADAQ8088EBZ

Brand: Analog Devices Pages: 12

EZ-KIT Lite ADSP-BF537

Brand: Analog Devices Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands