Silicon Laboratories Si5342 Family Reference Manual Download Page 46 | Manualshive

Page: 46 / 222

background image

Si5345-44-42-D-RM

46

Rev. 1.0

All phase delay values are restored to their default values after power-up, hard reset, or a reset using the RST pin.
Phase delay default values can be written to NVM allowing a custom phase offset configuration at power-up or
after power-on reset, or after a hardware reset using the RST pin.

6.6. Output Buffer Supply Voltage Selection

These power supply settings must match the actual VDDOx voltage so that the output driver operates properly.

Table 30. Output Delay Registers

Register Name

Hex Address [Bit Field]

Function

Si5345

Si5344

Si5342

N0_DELAY

0x0359[7:0]-

0x035A[7:0]

0x0359[7:0]-

0x035A[7:0]

0x0359[7:0]-

0x035A[7:0]

Configures path delay values for each N
divider. Each 16 bit number is 2s comple-
ment. The output delay is Nx_DELAY/(256
x Fvco) where Fvco is the frequency of the
VCO in Hz and the delay is in seconds.
Register values determined using Clock-
Builder Pro.

N1_DELAY

0x035B [7:0]-

0x035C[7:0]

0x035B [7:0]-

0x035C[7:0]

0x035B [7:0]-

0x035C[7:0]

N2_DELAY

0x035D[7:0]-

0x035E[7:0]

0x035D[7:0]-

0x035E[7:0]

—

N3_DELAY

0x035F[7:0]-

0x0360[7:0]

0x035F[7:0]-

0x0360[7:0]

—

N4_DELAY

0x0361[7:0]-

0x0362[7:0]

—

—

Table 31. OUTx VDD Settings

Setting Name

Description

OUTx_VDD_SEL_EN

These bits are set to 1 and should not be changed

OUTx_VDD_SEL

These bits are set by CBPro to match the expected VDDOx voltage.
0 = 1.8 V, 1 = 2.5 V, 2 = 3.3 V

«
...
44
45
46
47
48
...
»

Summary of Contents for Si5342































































































































































































































Reviews:

No comments

Related manuals for Si5342

Kinetic FLT 80 D5/DDC Body

Brand: EK-Quantum Pages: 16

Brand: Renesas Pages: 20

LBON320AC Series

Brand: Lindsay Broadband Pages: 4

High-Precision AD/DA Board

Brand: Waveshare Pages: 8

Brand: ETAS Pages: 29

Brand: AMC Pages: 28

Brand: Matrix Switch Corporation Pages: 48

Brand: Ciara Pages: 14

Brand: ADC Pages: 29

Brand: Telit Wireless Solutions Pages: 79

WIRELESS-G CARDBUS PC CARD - GUIDE D

Brand: Hawking Pages: 26

Brand: StarTech.com Pages: 10

Brand: Swyx Pages: 5

Brand: Edimax Pages: 88

PiggyBack 144QFP

Brand: Renesas Pages: 26

Brand: Barco Pages: 2

Brand: Targus Pages: 1

Brand: ORiNG Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands