Silicon Laboratories Si5342 Family Reference Manual Download Page 107 | Manualshive

Page: 107 / 222

background image

Si5345-44-42-D-RM

Si5345

Rev. 1.0

107

The R dividers are at the output clocks and are purely integer division. The R1–R9 dividers follow the same format
as the R0 divider described above.

Register 0x023F MXAXB Update

Reg Address

Bit Field

Type

Setting Name

Description

0x023F

0

S/C

MXAXB_UPDATE

Set to 1 to update the MXAXB_NUM and
MXAXB_DEN values. A SOFT_RST may also
be used to update these values.

Register 0x024A-0x024C R0 Divider

Reg Address

Bit Field

Type

Name

Description

0x024A

7:0

R/W

R0_REG

A 24 bit integer output divider
divide value = (1) x 2
To set R0 = 2, set OUT0_RDIV_FORCE2 = 1
and then the R0_REG value is irrelevant.

0x024B

15:8

R/W

R0_REG

0x024C

23:16

R/W

R0_REG

Table 48. Registers that Follow the R0_REG

Register Address

Description

Size

Same as Address

0x024D-0x024F

R1_REG

24-bit Integer Number

0x024A-0x024C

0x0250-0x0252

R2_REG

24-bit Integer Number

0x024A-0x024C

0x0253-0x0255

R3_REG

24-bit Integer Number

0x024A-0x024C

0x0256-0x0258

R4_REG

24-bit Integer Number

0x024A-0x024C

0x0259-0x025B

R5_REG

24-bit Integer Number

0x024A-0x024C

0x025C-0x025E

R6_REG

24-bit Integer Number

0x024A-0x024C

0x025F-0x0261

R7_REG

24-bit Integer Number

0x024A-0x024C

0x0262-0x0264

R8_REG

24-bit Integer Number

0x024A-0x024C

0x0268-0x026A

R9_REG

24-bit Integer Number

0x024A-0x024C

«
...
105
106
107
108
109
...
»

Summary of Contents for Si5342































































































































































































































Reviews:

No comments

Related manuals for Si5342

Brand: D-Link Pages: 38

Web Smart DES-1210-28P

Brand: D-Link Pages: 6

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 23

Express EtherNetwork DI-604

Brand: D-Link Pages: 7

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 97

Brand: Maxim Pages: 26

Brand: Cypress Semiconductor Pages: 11

Brand: ZALMAN Pages: 4

Brand: MC Pages: 21

Digital Encoder Plus

Brand: IDT Pages: 98

Brand: SSV Embedded Systems Pages: 17

Brand: Omron Pages: 6

Brand: PADAUK Pages: 27

VAR-SOM-MX8M-PLUS

Brand: Variscite Pages: 2

Brand: ETAS Pages: 68

Brand: Mitsubishi Pages: 188

Brand: ZALMAN Pages: 9

Instruction Card Video DC Block

Brand: Extron electronics Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands