Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 97

Page: 97 / 164

Output A and B as pulse volume

PW 5, 10, 50 100 & 500 mS

①

Forward

Pulse rate

②

Reverse

Pulse frequency

③

Cut-off

Pulse width

MAG 8000
When output A or B is configured as volume per pulse, the output delivers a pulse when the

preset volume based on either Forward/Reverse or Net Forward/Net Reverse flow has passed

the sensor in the selected direction. The volume per pulse is freely scalable, from 0.000001

to 10 000 units per pulse, and should not exceed the pulse rate of the output configuration

table.
MAG 8000 CT
The volume per pulse is defined in the MAG 8000 CT version to 0.001 or 0.01 or 0.1 or 1 m

per pulse.

Output B as alarm output

①

Alarm output

②

Alarm status

③

On - Off

④

No Error

MAG 8000
When output B is configured as an "alarm" output, it will follow the internal alarms that were

previously chosen in the Alarm Configuration List (Page 50).

Note
Alarm output is inverted to a pulse output providing an alarm if power disappears or cable

connection is interrupted.

Technical data

10.6 Output characteristics

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

Summary of Contents for SITRANS F M MAG 8000





































































































































































Search results

Summary of Contents for SITRANS F M MAG 8000

Reviews:

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 97 / 164

Search results

Summary of Contents for SITRANS F M MAG 8000

Reviews: