manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 31 / 164

Share
Download
Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 31

Connecting

5

This chapter consists of general safety requirements as well as a description of how to connect 

the device.
The connection of the device is done in four steps.
1. Wiring sensor and transmitter (remote version only).
2. Connecting power supply.
3. Connecting outputs.
4. Connecting add-on module.

Connection diagram

①

Module Interface (Option)

②

Output A

③

Output B

The 3.6 V DC battery connector - male and pulse connection terminals are placed in the right 

side of the PCB board - see figure.
Connection for add-on interface modules is placed on the left side.
HL = Hardware lock key connection
V = Verification button (enables verification mode for 4 hours)
To configure the outputs via PDM, see "Output configuration" (Page 53).
To configure the outputs via Flow Tool, see "Output configuration" (Page 125) in the Flow Tool 

appendix.

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

31

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments