manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 136 / 164

Share
Download
Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 136

Flow rate unit (parameter 9)

Correction factor parameter 301

BBL42/h

22643.31867

BBL42/d

543439.6482

C.2

Parameter lists

Parameter lists   

MAG 8000 is delivered with factory settings that are not stored as default values. Because 

defaults values are not present in the meter, an automatic return to factory values is not 

possible. 
The default settings are available at www.siemens.com/flow (

www.siemens.com/flow

). 

Navigate to Tools & Downloads under MAG 8000.
Visible display information is indicated in the table by menu and index number. Remember to 

enable displayed menus in parameter 130.
The abbreviations used in the display menu table are: Operator menu = O, Meter menu = M, 

Service menu = Se, Data Logger menu = L, Statistic menu = St, Revenue menu = R.
Factory settings marked in 

italic cannot be edited.

Note
Change of units
If the unit and factor is changed, all unit-related values become invalid.

It is recommended to reset all unit-related values.

C.2.1

1-99

Param‐

eter ID

Meter
version

Display
view

Parameter/data type

Factory settings

Data range

 

 

 

 

Fixed parameter or meter data that are not changeable

1

All

M1

Application identifier

Identity

Max. 15 characters.

Only numbers are visible in the 

display (letters are shown as "_")

2

All

-

Application location

Location

Max. 16 characters

3

All

M3

Module type

MLFB dependent

MAG 8000 Basic

MAG 8000 Advanced

MAG 8000 CT Basic

MAG 8000 CT Advanced

MAG 8000 Irrigation

4

All

M4

Software version

 

x.xx

5

All

-

Sensor size

Sensor related

Max. 12 characters.

DN 25 to 1200 (1" to 48")

Appendix
C.2 Parameter lists

SITRANS MAG 8000

136

Operating Instructions, 11/2018, A5E03071515-AE

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments