manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 102 / 164

Share
Download
Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 102

Siemens offers accredited calibrations assured to ISO 17025 in the flow range from 0.0001 

m³/h to 10 000 m³/h.
Siemens Flow Instruments accredited laboratories are recognized by ILAC MRA (International 

Laboratory Accreditation Corporation- Mutual Recognition Arrangement) ensuring 

international traceability and recognition of the test results worldwide.
The selected calibration determines the accuracy of the water meter. A MAG 8000 (7ME6810) 

standard calibration results in max. ±0.4% of rate ±2 mm/s uncertainty. A MAG 8000 

(7ME6880) standard calibration results in max. ±0.8% of rate ±2.5 mm/s uncertainty. An 

extended calibration of the MAG 8000 (7ME6810) sizes DN50 (2") to DN 300 (12") results in 

a max. ±0.2% of rate ±2 mm/s uncertainty. A calibration certificate is included with every sensor 

and calibration data is stored within the meter.

)ORZUDWHPV

(UUR

U

s

(

①

MAG 8000 Irriga‐
tion

Standard calibra‐
tion

±0.8 % of rate ±2.5 mm/s

②

MAG 8000 Stand‐
ard

Standard calibra‐
tion

±0.4 % of rate ±2 mm/s

③

MAG 8000 Stand‐
ard

Extended calibra‐
tion

±0.2 % of rate ±2 mm/s

Calibration references conditions (ISO 9104 and DIN EN 29104)
Media temperature: 20°C ± 5K (68°F ± 9°F)
Ambient temperature: 20°C ± 5K (68°F ± 9°F)
Warming-up time: 30 min.
Incorporation in pipe section
Inlet section: 10 x DN
Outlet section: 5 x DN
Flow conditions: Fully developed flow profile

Technical data
10.7 Meter uncertainty

SITRANS MAG 8000

102

Operating Instructions, 11/2018, A5E03071515-AE

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments