Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 53

Page: 53 / 164

6.4

Unit selection

The device is delivered with totalizer and flow rate units in m and m

/h, respectively, as

standard. However, it is possible to manually configure the device to operate with other units.

Changing the units

1. Select "Device" → "Unit guide".
2. Select the new unit from the list.
3. Click on "Apply Change of Units".

Afterwards, the change must be stored into the transmitter via "Download to Device".

6.5

Output configuration

Pulse output can be configured as volume pulse, alarm or call-up. Default factory setting is

with output A enabled for forward flow and output B for alarm output.

Output configuration in SIMATIC PDM
Select "Output". The software window shows the parameters for output configuration. Each

parameter has its own guideline for selecting the correct parameter setting.

Commissioning

6.5 Output configuration

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

Summary of Contents for SITRANS F M MAG 8000





































































































































































Search results

Summary of Contents for SITRANS F M MAG 8000

Reviews:

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 53 / 164

Search results

Summary of Contents for SITRANS F M MAG 8000

Reviews: