manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 162 / 164

Share
Download
Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 162

Meter utilization (Advanced version only)
6 registers for monitoring total time the meter has operated in different flow intervals. 

Registered intervals are freely selectable as % of Qn (Q3).
Tariff (Advanced version only)
6 tariff registers count the volume delivered within the selected tariff windows, based on time 

of day, flow rates, or a combination.
Tariff can also be used for consumption profile where consumption is related to different time 

intervals or flow rates.
Tariff values visible on the display.
Settling date (Advanced version only)
At midnight (23:59:59) on a predefined date the totalizer 1 index value is stored. Old values 

are stored to show the latest two totalized 1 index values. Settling values are visible on the 

display.
Statistic (Advanced version only)
● Min. flow rate with time and date registration
● Max. flow rate with time and date registration
● Min. daily consumption with date registration
● Max. daily consumption with date registration
● Latest 7 days' total and daily consumption
● Actual month's consumption
● Latest month's consumption

Appendix
C.6 Features

SITRANS MAG 8000

162

Operating Instructions, 11/2018, A5E03071515-AE

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments