manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 158 / 164

Share
Download
Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 158

C.6

Features

Feature

MAG 8000 basic

MAG 8000 advanced

Measurement frequency

(battery power)

Max. 1/15 Hz

Max. 6.25 Hz

For MAG 8000 Irrigation 

(7ME6880):

Max. 3.125 Hz

Totalizer

3

3

Pulse output

2, max. 50 Hz

2, max. 100 Hz

Communication

Add-on

Add-on

IrDA

Yes

Yes

Time and date

Yes

Yes

Data protection

Yes

Yes

Data logger

Yes

Yes

Application identifier

Yes

Yes

Alarm handling

Yes

Yes

Meter status

Yes

Yes

Diagnostics

Yes

Yes

Battery power management

Yes

Yes

Insulation test

-

Yes

Leakage detection

-

Yes

Meter utilization

-

Yes

Statistics

-

Yes

Tariff

-

Yes

Settle date (Revenue)

-

Yes

Features

Application identification (parameters 1 and 2)
Tag number (visible on display if numbers are selected) and meter location, up to 15 characters 

per information.
Time and date (parameter 100)
Real time clock and date (max. 15 minutes drift per year)
Totalizer (parameters 101, 102 and 103)
● 3 totalizers: Forward, reverse, bidirectional netflow calculation and freely selectable start 

value.

Note
CT version
The totalizers are not resettable for the CT version.

Appendix
C.6 Features

SITRANS MAG 8000

158

Operating Instructions, 11/2018, A5E03071515-AE

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments