Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 152

Page: 152 / 164

C.2.8

800-899

Param‐

eter ID

Meter
version

Display
view

Parameter/data type

Factory settings

Data range

Fixed parameter or meter data that are not changeable

800

Advanced -

Insulation test enable

Yes / No

Value is reset to "No" when up‐

loading device parameters to pc

after 4 minutes

801

Advanced -

Insulation test interval

0 to 65535

802

Advanced -

Insulation value

803

Advanced -

Insulation test date

2000-01-01 T00:00

year-month- day T hours:mi‐

nutes:seconds

804

Advanced -

Insulation tests fulfilled

810

Advanced -

Leakage detection mode

Off

Off / fixed limit / fixed

limit

811

Advanced -

Leakage source

Flow rate

Flow rate / volume

812

Advanced -

Start period for leakage

detection

120 min = 2:00 [24:00]

0 to 1440 detection minutes (0

to 23:50)

813

Advanced -

Duration leakage detec‐

tion

0 to 144 (10 to 1440 minutes)

814

Advanced -

Leakage value unit

Flow / volume unit

The unit is updated once param‐

eter 811 change is downloaded

to the device and afterwards up‐

loaded to the pc

815

Advanced -

Leakage limit

0 to 1x10

The unit is updated once param‐

eter 811 change is downloaded

to device and afterwards uploa‐

ded to pc

816

Advanced -

- Leakage excitation fre‐

quency

1.5625 Hz

1/60 Hz, 1/30 Hz, 1/15 Hz,

1/5 Hz, 1.5625 Hz, 3.125 Hz,

6.25 Hz

Appendix
C.2 Parameter lists

SITRANS MAG 8000

152

Operating Instructions, 11/2018, A5E03071515-AE

Summary of Contents for SITRANS F M MAG 8000





































































































































































Search results

Summary of Contents for SITRANS F M MAG 8000

Reviews:

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 152 / 164

Search results

Summary of Contents for SITRANS F M MAG 8000

Reviews: