manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 125 / 164

Share
Download
Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 125

A.6

Output configuration

Pulse output can be configured as volume pulse, alarm or call-up. Default factory setting is 

with output A enabled for forward flow and output B for alarm output.

Output configuration in Flow Tool
Select "I/O and Com.Setup". The software window shows the parameters for output 

configuration. Each parameter has its own guideline for selecting the correct parameter setting.

To see how the outputs work, please see "Output characteristics" (Page 96).

A.7

Default display information and accessible display menus

Parameter 131 defines default display information with selection between
● Totalizer 1 (Index 1)
● Totalizer 2 (Index 2)
● Flow rate (Index 3, updated with selected measuring frequency)
● Fault codes (Index 4)
● Customer totalizer (Index 5 - resettable)
Default information is shown after power-up as well as after no key operation for 10 minutes.
Parameter 130 defines accessible display menus with selection of one or more of the following 

menus:
● Operator menu
● Meter info menu
● Service menu
● Data logger menu

Flow Tool

A.7 Default display information and accessible display menus

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

125

Summary of Contents for SITRANS F M MAG 8000





































































































































































Reviews:

No comments