Siemens SITRANS F M MAG 8000 Operating Instructions Manual Download Page 39

Page: 39 / 164

Encoder interface connection diagram

①

Black wire

②

Red wire

③

Unshielded wire

④

Endpoint

Figure 5-1

Encoder interface cable connection between MAG 8000 and ITRON 200WP with Itron cable

Connect black wire to terminal 91, red wire to terminal 92 and unshielded wire to terminal 93.

WARNING

Unshielded wire
It is important that unshielded wire does not touch any metal parts of MAG 8000 housing.

Other radio interface cable has to be a 3-wire cable with a shield connected to MAG 8000

housing (mounting cable shield is shown to the right).

GND

Data

129.10.10

①

Power clock

②

Connect shield to encapsulation

③

Radio interface

Connecting

5.5 Communication modules

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

Summary of Contents for SITRANS F M MAG 8000





































































































































































Search results

Summary of Contents for SITRANS F M MAG 8000

Reviews:

Siemens SITRANS F M MAG 8000, Operating Instructions Manual, Page: 39 / 164

Search results

Summary of Contents for SITRANS F M MAG 8000

Reviews: